MANUFACTURING
Syringe Barrel Defect Detection
Syringe Barrel Defect Detection. What it takes to run it.
Every barrel off the mold boxed for a crack, a short shot, flash or contamination, before the tray closes.
// 01 · The question
“Which barrel in this shot is cracked, short, flashed or contaminated, boxed before the tray closes rather than found at the next hourly pull?”
// 02 · Why it is hard
The barrels are clear resin, lying at whatever angle the robot set them down, under an overhead light that flickers when the press heaters cycle. A crack catches that light differently from a scuff, and a speck of contamination can be a fleck of dust on the lens as easily as resin. A model fitted to bench photographs under a lamp is confident on the bench and wrong on the outfeed.
// 03 · What the labels have to be
Bounding box
Decided before the first frame
A crack, a short shot, a flash line and a speck of contamination are each a yes-or-no call on one barrel, not a quantity to size. A box finds which barrel and where on it, which is what points the molding technician at a cavity to check; a mask would cost labeling time measuring an area nobody disposes against.
This is the decision that is expensive to reverse. The geometry has to match what the answer contains, and finding out it does not means labelling the set a second time.
// 03a · What it finds
A crack along the barrel wall
boxed on every barrel the robot sets onto the outfeed conveyor, whatever angle it landed at
A short shot
the flange or tip left incomplete where the cavity did not fill, found the same way on the same frame
Flash and contamination
excess resin along the parting line, or a speck or streak in the clear resin, boxed on the barrel it sits on
A barrel the model cannot place
a scuff that could be a crack, a shadow that could be flash, held for a person with the frame rather than scored either way
// 03b · What it checks
- 01
The box against a person's eye, mostly at the line between a scuff and a crack, or a shadow and flash, since the outfeed light catches each differently from the bench lamp the defect sheet was written under.
- 02
The rule's own severity and cooldown, a crack or a short shot set critical, flash and contamination set routine, so one alert goes to the shift and the other waits for the hourly list.
- 03
A barrel the model doubts, held for a person with the frame rather than silently passed or silently rejected.
- 04
The technician's override rate after a resin or tooling change, since a barrel that looks different for a documented reason is a labeling job, not a model fault.
// 03c · What the line provides
- The camera already over the outfeed conveyor; no new camera and no new hardware on the line.
- Frames from this press's own outfeed, at its mounted position, across shifts and across the heater's flicker, not a bench photograph. A model trained on the bench is wrong on the line.
- The four class names fixed before labeling, in the molding technician's own words, crack, short shot, flash, contamination, so a defect is called one thing rather than two.
- Someone to read the alert and clear the barrels it holds, the same tray-sorting job done faster with a crop already in hand.
// 04 · How we run it
Three parts of one loop, on this job.
LexAnnotate
Defect Annotation
Pixel-level defect annotation for surface scratches, cracks, dents, weld faults, and assembly misalignments. Multi-sensor alignment for multi-camera inspection systems.
LexInsight
Line Performance
Ask which shift or which line is producing the most of one defect class, and get an answer with the frames behind it, graded against the plant's own written standard.
LexAlert
Quality Alerts
Monitor defect detection accuracy across changing production conditions. Detect when lighting shifts, new materials, or equipment aging degrades model performance. Auto-retrain to maintain 99%+ accuracy.
// 05 · What breaks it after launch
A new resin lot runs slightly less clear, or the tool comes back from a polish with a different parting line, and the barrels look different in ways a person barely notices. The pixels changed; the taxonomy did not. The signal is not in any one frame but in the technician's own overrides climbing on the first shift of the new lot.
It is not the only one that can get this use case, it is the one that usually gets it first. All ten conditions.
// 06 · In manufacturing
Defect Detection at Scale
The Challenge
Vision models performed well in pilots but lost accuracy as factory conditions shifted.
Our Execution
Built pixel-level annotated datasets and multi-sensor alignment for reliable defect detection.
The Result
Maintained 99%+ defect detection accuracy across changing production environments. Reduced unplanned downtime.
99%+
Accuracy maintained in production
// 06a · Questions we get asked
Does this tell me which cavity made the defect?
No. It boxes the defect on the barrel as it reaches the outfeed camera. Connecting that find back to a cavity is the technician's own read of the shot and the robot's set-down order, the same read as before, now made against a crop instead of a barrel pulled from a tray.
What happens to a barrel it cannot decide on?
It is held for a person with the frame rather than passed or rejected on a guess. The scuff-or-crack and shadow-or-flash cases are the usual ones; the verdict becomes a label, and the next version has learned that case.
Does a crack and a flash line get treated the same way?
No. The rule sets its own severity and cooldown per class: a crack or a short shot is set critical, since a cracked barrel that ships is a recall; flash and contamination are set routine, since a flashed barrel that ships is a customer note. Both go out as an alert with the frame; what differs is who sees it and how fast.
What happens when the resin or the tool changes?
Nothing in the frame announces it. What shows up instead is the technician overriding the model on one class, in one direction, more often than usual. That override rate is the signal; a window of frames from the new lot or the polished tool is labeled and folded in, and the version trained on the old barrels stays available for any stock still on the line.