MANUFACTURING
Semiconductor Wafer Inspection
Semiconductor Wafer Inspection. What it takes to run it.
Cracks, scratches and edge chips masked on the wafer at intake, sized against the fab's own limit before it reaches lithography.
// 01 · The question
“Is that bright streak on the wafer a scratch past the limit, or the ring light again, before the cassette moves to lithography?”
// 02 · Why it is hard
The wafer is a mirror. Under the bright-field ring light the surface throws back a highlight that is a bright streak at the wrong angle, indistinguishable from a scratch unless the frame is built to separate the two. A scratch itself is a few pixels wide across a wafer that is mostly clean, so a model evaluated on a frame scaled down to its input size loses the defect before it is ever found, and the good wafers vastly outnumber the bad ones by construction.
// 03 · What the labels have to be
Instance segmentation
Decided before the first frame
A crack is a reject whatever its size, so a box alone would carry that one class. But a scratch is a severity call on its length and an edge chip is a severity call on its area against a written limit, and neither length nor area comes from a box. Only a mask carries the measurement the disposition needs, so the extent-sensitive classes set the geometry for all three.
This is the decision that is expensive to reverse. The geometry has to match what the answer contains, and finding out it does not means labelling the set a second time.
// 03a · What it finds
A crack along the wafer
boxed on every wafer in the cassette under the intake camera's bright-field ring light, since a crack of any size is a reject
A scratch across the surface
masked on two frames of the same wafer at two chuck positions, since a true scratch is still there in both and a ring-light highlight is not
An edge chip
masked at the wafer's edge, its area read against the fab's own written size limit
A wafer the model doubts
a streak that only appears at one chuck tilt, or a chip close to the limit, held at intake for the technician before the cassette moves on
// 03b · What it checks
- 01
A scratch against the two-tilt rule before it is masked at all, so a highlight the wafer throws back at one angle is never written down as a defect.
- 02
The scratch's length and the chip's area against the fab's own written limit, read off the mask rather than guessed from a box.
- 03
The rule's own severity and cooldown, approved before it goes live, so a crack or an over-limit chip pages the intake tool's screen and the process engineer and a monitored chip waits for the shift list.
- 04
The technician's override rate after a spec change, since a tightened limit moves what counts as a reject without changing a single pixel the camera sees.
// 03c · What the line provides
- The intake camera already mounted over the chuck, under the bright-field ring light the fab already runs; no new camera.
- Two frames of the same wafer at two chuck positions, since the labeling rule that tells a scratch from the ring light's own reflection needs both.
- The frame tiled at full resolution before the model sees it, since a one-pixel scratch disappears if the whole wafer is scaled down to the model's input size.
- The written limit for scratch length and chip area from the fab's own spec, since the model measures the extent and the limit is what turns that measurement into monitor or reject.
// 04 · How we run it
Three parts of one loop, on this job.
LexAnnotate
Defect Annotation
Pixel-level defect annotation for surface scratches, cracks, dents, weld faults, and assembly misalignments. Multi-sensor alignment for multi-camera inspection systems.
LexInsight
Line Performance
Ask which shift or which line is producing the most of one defect class, and get an answer with the frames behind it, graded against the plant's own written standard.
LexAlert
Quality Alerts
Monitor defect detection accuracy across changing production conditions. Detect when lighting shifts, new materials, or equipment aging degrades model performance. Auto-retrain to maintain 99%+ accuracy.
// 05 · What breaks it after launch
The fab tightens the chip limit for the next product and the wafers coming off the line look exactly the same as last month's. Every label that said monitor on a chip of that size is now wrong, and nothing in the frame announces it. The first sign is the technician's override rate climbing on wafers the intake verdict used to pass.
It is not the only one that can get this use case, it is the one that usually gets it first. All ten conditions.
// 06 · In manufacturing
Defect Detection at Scale
The Challenge
Vision models performed well in pilots but lost accuracy as factory conditions shifted.
Our Execution
Built pixel-level annotated datasets and multi-sensor alignment for reliable defect detection.
The Result
Maintained 99%+ defect detection accuracy across changing production environments. Reduced unplanned downtime.
99%+
Accuracy maintained in production
// 06a · Questions we get asked
Does this read the wafer the way the technician does at intake?
It looks at every wafer in the cassette the same way, at a resolution the eye does not have, and boxes or masks what it finds. Deciding what a found defect means against the fab's own limit is the rule's job; a technician still holds up the wafer the model was surest about, the one nobody else would have looked at twice.
How does it tell a true scratch from the ring light's own reflection?
Mostly from a labeling rule, not the model alone. A streak only counts as a scratch if it is still there when the wafer is tilted to a second chuck position; a highlight moves with the light and a true scratch does not. Frames where that is still unclear are held for a person before anything is scored.
Can it find a scratch that is only a pixel or two wide?
Only if the frame is tiled first. Scaling a full wafer down to the model's input size erases a thin scratch before the model ever sees it, so the frame is cut into overlapping full-resolution patches, the model runs on each, and the boxes are merged across the seams.
What happens when the fab tightens the chip limit?
The wafers look the same and the camera is the same, but a chip that was monitored last month is a reject this month. Because the model measures the extent and a rule decides against it, the fix is the number in the rule on the day the spec changes; the signal if it goes unrecorded is the technician's override rate climbing on wafers the old limit used to pass.
// 07 · Also in manufacturing